How To Spool A Baitcaster With Backing

November 13, 2020

This is in the case of using a monofilament. Then, even though i try to keep it even across the spool, i always end up with the tape being thicker towards the sides of the spool where it slopes up.

Thats a bit better.

Do not add an excess line to your spool, as this will prevent you from pulling off smooth casts.

How to spool a baitcaster with backing. I do this on both my casting and spinning reels. To prevent this, you should coat the spool’s base with some sort of grippy material. You can use the length of your old monofilament for the backing.

For baitcasters, spool your line up to a 1/8” from the top of the spool mounts on either side of the spool. The braided line tends to slip a lot on the spool. An arbor knot is your best choice if you are thinking of spooling a baitcaster with monofilament backing.

For the mono backing line, i recommend using 15lb berkley trilene big game which i also recommended as the best beginners baitcasting line further up the article. This will ensure you have the perfect amount of line on your reel without having too much braid or mono. This will put the braid on top now, so you’ll have just the right amount of mono and braid.

First, get your equipment ready. Having less line on a baitcaster spool, allows the spool to spin more freely increasing it's efficiency and your distance. The easiest way round it is to use a monofilament backing on the spool before adding braid to the top.

It was only when i picked up fishing in the uk around 2011/2012 that i discovered the benefits of using braid when learning to work jerkbaits for pike. Key pointers on how to spool a baitcaster with a braid. Braid backing gives you a lighter spool than mono.

Our first goal is to teach you first how to put a spool braided line on a baitcaster. But learning to spool a braided line on baitcaster reel is an art that has to be experienced with the help of video lessons and tutorials, gradually to achieve perfection. Attach the mono right through the braided line if you will be using a double uni knot.

All the baitcaster are mounted on top of. Still be sure to keep plenty of tightness on the line as you reel line onto the spool. Tie on a little bit heavier lure than you are going to throw with this combo and make some casts.

Feed the monofilament line through the worm guide and tie it to the spool. (i remove the spool from the reel to do this) i wrap back and forth until i get the amount i want on the spool. Fill your spool up with whatever backing you decide on that is roughly the same diameter that your main line is going to be.

This will help you to avoid line twists and back lashing. I put monofilament or fluorocarbon backing — old line — on my reels before i spool the braid. But if your number one goal is to get your braid right on the baitcaster, you need to keep these important things in mind.

Put the spool braided line on a baitcaster. Fill spool until there’s a 1/8th inch gap left at the edge of the spool. I try and fill my reels fairly close to the edge of the spool, as you will lose line quickly from tying on baits.

The next step is wrapping your line around the spool and to secure it by trying an overhand knot. Spool a few turns until you have a layer of the mono across the spool. It keeps the braid from slipping and cutting into itself so much and it saves expensive line.

For the most part, especially when bottom. Trim off line end from the knot. You also don't have line rubbing on the frame from being too full.

Transfer the line onto your other reel. The line will go over this backing. I just got a curado k and some 40 lb braid.

The main consideration when spooling a baitcaster is the line size and type of line you will be adding to the reel. How to spool braid onto a baitcaster explained. Monofilament and fluorocarbon can be used for the backing but monofilament is recommended.

Start spooling line on to the reel by turning the handle. With a baitcaster, you can cast to the very bottom of the spool with the same lack of friction as you would if the spool was full. While spooling a braided line to your baitcaster reel you must have a backing so it does not slip.

The key is to stretch it firmly to get a tight wrap and good grip on the spool. The money issue is even easier to solve than the backlash issue. Set up the baitcaster for it to level to the spool of the line to use.

Although casting a baitcaster is tougher for most new angler than a spinning reel, it is typically much easier to spool. My backing line is usually older mono or some left over end piece from a spool of line that is not long enough to spool up a reel. Hey guys, i have a few questions about using backing on a baitcaster as ive never done it before.

How much of the spool should i fill with mono before tying on the braid, and what knot is best to use? Follow these quick steps to ensure you do it correctly! That means something if you are casting lighter lures.

These art lessons directly begin with learning how to spool a baitcasting reel with braided line correctly. This process applies if you’re using monofilament or fluorocarbon to fill your baitcaster. Tie the backing to your braid and fill the rest of the spool up with the backing.

Certain line types are thicker than others at. I typically tie a “j” knot on my backing to my fishing line on the top. Use a backing on the baitcaster spool.

For most of my fishing life i had used mono as my mainline. Tie line to spool of the baitcasting reel. A baitcast reel is the hardest reel for a beginner to learn to cast without backlashing.however, beginners will be glad to know that it is much easier to spool line on a baitcaster than on a spinning or spincast reel.

Use monofilament backing when spooling your fishing reel. With a baitcaster, the level wind should lay line down evenly across the entirety of the reel without any of your assistance. The main advantage of using a mono backing is cost.

There are a number of steps and techniques to do it correctly. The type of line you are using, decides the type of knot that you should have in order to spool a baitcaster. Will 14 lb mono be good to use as backing?

If you don’t fill your reel with line, you’ll lose a lot of casting distance because the gap between the top of the spool and the line will cause friction as it’s leaving the reel. It is a good quality line with a very attractive price, which makes for a perfect line to fill up the first part of your spool. How to spool your baitcaster reel avoid equipment worries on the water this fishing season and spool your baitcasting reel the right way with help from these spooling tips and tricks.

Bass Fishing Tips For Beginners My 2nd Rod And Reel