How To Install Ridge Vent Cap Shingles

January 28, 2021

Repeat with the other ridge caps to cover the whole roof. When ridge vent installation is performed correctly, the vent increases the home’s energy efficiency and extends the life of the roof.

Ridge Vent installed with Independence Shingle American

Butt the edge of the first cap shingle along this line.

How to install ridge vent cap shingles. Installing plastic ridge vent for attic venting. Baffled vents are suggested because they prevent airflow back into the attic through the ridge vent, while still allowing hot air to escape. The shingle cover/cap matches the other tiles on the roof, and it provides some protection to the plastic ridge vent.

No end cap is necessary if ridge cap shingles are lapped over end of. If using fabric end cap, hang shingles 1 over vent at gable ends. Hip and ridge cap shingles 101:

Install asphalt shingle caps over the vent, using the nails recommended by the manufacturer. The cap shingles often are installed on top of a continuous ridge vent. Make sure to trim the second to last ridge vent section to assure the self closing end is installed properly at the end of the ridge.

Use nail line as placement guide. A properly installed ridge vent increases energy efficiency and prolongs the life of your roof. If necessary, trim any excess ridge cap to fit your roof length.

Use roofing cement to attach the leading edge of this ridge cap piece to the shingles below. A cedar shake roof ridge cap isn't difficult to create. How to install the last shingle on ridge cap.

Align the first ridge cap piece with the end of the shingles and the chalk line. The process to install ridge cap shingles has changed because roofing market trends have favored a new type of shingle. For ridge cap shingles without closures, you can skip to step 5.

In summary, to install the ridge cap shingles, you simply separate them where they are perforated, “bend” them over the peak, and nail them down. Both systems require the same creation of the ridge vent openings as described in the steps above. To cover the ridge, install vented cap shingles or continuous ridge vent.

Bend single tabs (or special ridge shingles) over the ridge, beginning at the end putting a bead of asphalt under the first ridge shingle to hold down the tab. A ridge vent is an important part of a home's roofing system. Measure down 6 inches from the center of the roof ridge and chalk a line parallel with the ridge.

Center ridge cap shingles over vent and install with 1 3/4 collated nails provided. Install the new ridge vents using long roofing nails. A ridge vent is designed to allow air to flow freely from the attic.

Installing the last shingle on the ridge cap or roof isn’t hard. The nails should be long enough to penetrate through the vent, shingles, and securely into the sheeting beneath the shingles. When installing a ridge vent, first apply ridge caps along the ridge, place the ridge vent in place and secure it to the roof, then put another layer of ridge cap shingles over the ridge vent.

This video shows exactly how to cut the last shingle, use roofing cement, nail the last shingle on the ridge cap, then hide those nails. You may have to paint a metal ridge vent to match the roof. Make sure they overlap at the right position to hide the nails/screws.

The next step is to cap the ridge. Nail it where the next ridge shingle will cover the nails about an inch horizontally and vertically. Line the entire roof peak with a good adhesive membrane that the roof caps will adhere to.

The difference between the two systems is that with a shingle over the ridge vent system, shingles are used to cover the ridge vent. Nails must penetrate into sheathing 3/4 or completely through the sheathing. These shingles match the other shingles used.

Start on the end of the ridge opposite to the prevailing winds. Then they nail it along the edge every 6 to 10 inches. They are a shingle over the ridge vent or an aluminum ridge vent cap.

When capping the ridge vent, use these lines to properly place your nails. Installed at the peak of a sloped roof, the ridge vent allows damp, warm air to escape from the attic. And then cap the ridge vent with appropriate capping.

It’s made from a permeable material and is placed on top of the metal roofing panels at the ridge of the roof. Fasten the ridge cap on the ridge vent using screws or roofing nails. See the benefits of hip and ridge cap shingles a new roof is more than just shingles.

Finally, there are the nail guide lines. You can see me do that in the video below. Line up the edges with the chalk line and secure with 2 roof nails right above the adhesive line on the shingle tab.

Nail on both sides of the ridge behind the area that will be covered with the next piece. Our ridge vent is a plastic piece with vents on either side of the roof. The shingle should be in the center of the ridge.

Make sure all shingles on each side are covered. The roofer said he could take those off and install “ridge caps”, but he’d have to cut along either side of the peak by about 4″, and although it would look better cosmetically, having shingles covering the peak, it would not produce as good ventilation as the ridge vent now sitting on top of the house and it would expose me to problems. Once all the shingles are nailed to the roof decking, construct the cedar shingles.

The ridge vent is then covered with a metal ridge cap.the purpose of the ridge vent is to create constant air flow along the horizontal ridge of your home. On top of each ridge vent, there is a shingle cover/cap. Attach the other side of the vent to the opposite side of the ridge to fully secure the vent.

Start at one of the eaves of the ridge and wrap a shingle around the ridge of the roof.

Turtle Vents vs. Ridge Vents Choosing the Right