How To Light Pilot Light On Gas Fireplace

January 20, 2021

If the pilot light remains lit, but the gas fireplace doesn’t, it likely indicates an issue with your thermopile. In order to continue to burn, though, a pilot light relies on a thermocouple, which sends an electric signal.

Firegear City Lights Propane Gas Peninsula Fireplace

There are vented gas logs and unvented or “vent free” logs.

How to light pilot light on gas fireplace. Most gas fireplaces rely on a “continuous pilot light,” a type of pilot that remains lit so long as gas is flowing to the unit. If the pilot does not light, wait 5 minutes and try again. I tried cleaning up gas line and pilot assembly which helped for a day or two but it never stayed lit very long.

More often than not, the pilot light can simply be reset in order to get your gas fireplace working properly once again. Now it doesn't come on at all however pilot light is on. This year when starting it up, it wouldn't ignite (pilot light on) then out of the blue it worked for awhile and then stopped.

Hold the gas control button down while you hold the end of a lighted match or lighter at the end of the pilot tube. Hold the knob in for at least 30 seconds. If you release and the pilot dies, you released too soon.

Press the knob on the gas valve while you click the sparker (don’t stop pressing the knob). Keeping the pilot light on will also keep moisture out of the unit and in turn, help prevent corrosion. To light gas logs safely, turn the control handle to the pilot position, press it in, light the pilot with a match and hold down the handle for half a minute until the pilots are burning on their own.

Push in the pilot knob, which manually sends gas into the system. The pilot should start as soon as the flame is close enough. To light a gas pilot, the button on the combination gas valve must be pushed down which allows gas to enter the pilot tube and exit through the pilot termination head.

To ignite the pilot light, press your finger into the center of the control knob and hold it in place. Continue doing this until the pilot starts. Started having trouble last year.

Turn the pilot control knob to the pilot position. Tap the switch until the pilot light ignites. As you can see, it's probably best in most cases to extinguish the pilot light in your gas fireplace during the months when you don't need heat.

You should hear a whoosh noise as it lights, and you should be able to see a little blue flame in the burner. Press the control knob down and hit the ignition switch. Gas fireplace won’t stay lit, but the pilot light does.

Turn the gas control until the “pilot” setting aligns with the mark on the outer rim of the control. If the pilot light is out, though, such a signal isn't sent. Always remove your fireplace glass prior to lighting your pilot * if you do not see a red or black spark ignitor button, you do not have a manual ignition system.

First, hold down the gas control button while also holding the end of your lighter or lit. Some appliances, such as a gas fireplace, may have an open pilot light area. If your pilot light stays lit, but the fireplace won’t start, then the problem is likely related to your thermopile, a metal probe (round and slightly smaller than your pinky finger) that converts heat from the burning pilot light’s flame into a tiny amount of electricity — just enough to open the gas valve when a switch (such as a wall.

The process is relatively simple and can save you in a jam. Intermittent pilot ignition (ipi) mode means that the pilot light will light and extinguish each time the unit is used, the ignition system will first ignite the pilot light before opening the gas valve to the main burner and igniting the fireplace. After lighting gas logs pilot light, set the handle to the “on” position.

However, if you find that your gas fireplace or similar appliance has a pilot light that won’t stay on even after consistently being fixed or relit, one of these issues could be the reason. Has the pilot light on your fireplace gone out? Leaving the gas on keeps this compound moving out of the tubes.

Set the gas knob to pilot. The pilot light on your gas fireplace is out and you can't get it going again. Turn the knob from the “off” to the “pilot” position.

The pilot needs to warm up or it'll die out right away. The following technique works on most regency, napoleon, valor, continental and vermont castings fireplaces that use a pilot system. It’s possible that excess moisture may have gotten into your gas line, causing the pilot light to malfunction.

A pilot flame is lit with a manual push button spark ignitor or a handheld lighter while pushing down on the pilot plunger button found on the top of the gas valve. Turn the off/pilot/on knob to the pilot position; Here's how to start that fire and get your toes toasty:

How to light your fireplace pilot. How to light or relight a pilot on a gas fireplace, insert or stove. Press and hold the knob in;

If the pilot doesn’t light, wait 10 seconds and push again. This is another relatively small piece of your fireplace that converts heat to electricity, ultimately opening up the gas valve when you turn on the fireplace. Push the button in while you push the starter.

How do you reset the pilot light on a gas fireplace? We can send a gas service technician to light your pilot, and conduct a gas safety check of your gas fireplace or any other gas appliance to ensure your safety. Has the pilot light on your heat & glo fireplace gone out?

Hold the pilot button down for about 20 seconds to give the thermocouple time to heat up, then release it. Hold the gas control button down. The pilot should stay lit.

A pilot light provides a flame that powers appliances like water heaters, furnaces and fireplaces. Click the piezoelectric igniter a few times until the pilot lights. Use a screwdriver to remove the screws to open the panel if needed.

A benefit of ipi mode is that it is more cost effective, efficient and environmentally friendly. Here’s how to light a gas fireplace with a control panel. Then, hit the fireplace’s ignition switch, which is typically a red button located near the control knob.

Decorative Logs Stone and Glass 38220 Fireplace Gas Log