How To Vacuum A Pool With A Cartridge Filter

March 11, 2021

A filter cartridge for the pool supports vital pool chemicals to perform better and achieve healthier pool water. A cartridge pool filter uses a filtration system made up of thin, clothlike material to filter out particles and contaminants from your pool water.

Intex 12' x 30" Easy Set Above Ground Pool, Filter Pump

How to vacuum the pool without using the filter

How to vacuum a pool with a cartridge filter. Run aqua comb over filter once; With the pump and filter running, take the other end of the hose and put it up against a return jet in the pool. I have a hayward cc 1000 filter cartridge system for my 24 round above ground pool.i recently read an article advising putting a a line into the drain port with a ball valve, so that you can bypass the filter when you are vacuuming the pool to waste.

The easiest way to vac to waste with a cartiridge filter is to leave the top off of the filter vessel. A cartridge filter system works by drawing water into a tank that houses cylindrical cartridges of fine, pleated mesh material. I didn't want the mess, so i had to make plumbing modifications to my cartridge filter to add the ability to vac to waste.

Cartridge filters will filter the water to perfection. Locate the on/off switch on your pool’s filter, usually near the pressure gauge, and switch it off. If you don't have valves at these connections, insert a plug into the skimmer to stop the flow of water into the pump and another plug at the pool inlet to prevent the water from.

I cleaned the filter (cartridge, above ground pool) filter is white and is only one year old. The cartridge can be removed periodically for washing, to remove dirt and debris, and then can be replaced with a brand new one every year or so. For routine vacuuming, the filter valve is left in the normal “filter” position.

I was told that cartridge filters can't vacuum to waste, but i don't know if that's true. This product is perfect for winterizing and draining pools and spas. The cartridges are then simply removed and washed when needed to keep them clean and functional.

How to vacuum the pool with a cartridge filter. Coming off of my pump is a spigot that allows water to freely drain when i need it to, such as when my water level is too high. Reassemble filter and run pool;

Bubbles will come up from the vacuum head on the floor of the pool. Once the bubbles stop, all the air is out of the hose. It allows water to pass through, but not solid objects.

Position the vacuum unit on the edge of the pool farthest from the pool's filter unit, and join hose segments together to reach from the vacuum unit to the skimmer basket. It can hold the particles of the size of 10 microns and they are 50 square feet big. A cartridge pool filter works by collecting the particles filtering through the pool.

I checked the hose, no leaks. Get a small vacuum hose and either put the hose in the funnel and put the funnel near the return in the pool with the other end of the hose out of the pool, so when you vacuum, the water will still come through the return, but be caught in the funnell, into the hose, and out over the side. Always do this to turn off the filter before you move the multiport valve to backwash the filter or you could break the diverter gasket inside the valve.

All of the pumped water will simply flow out the top. Cut the power to the filter, shut the valve from the filter outlet that goes to the pool inlet, and shut the valve that goes from the skimmer to the pump inlet. With the cartridge out, and the drain plug off, quickly vacuum all dead algae off the bottom of the pool.

Your goal is to make sure there is enough hose for the vacuum to reach all areas of the pool surface. After placing the cartridges back in the filter, securely replace the tank lid and close the clamp to seal the equipment. By stephen melamed (perry, fl) i cannot maintain a steady suction when vacuuming pool.

Disassemble the hoses, clean them, and then store them. I also have a valve before the filter that can be turned to prevent the water from going into the filter. If your pool uses a cartridge filter, the following are the steps.

Final words to sum things up, using a sand filter to vacuum a pool is a critical factor in enhancing a proper environment for the users. You will easily notice that a portable pool vacuum system is clogged because it will start returning the dirt through the hose. Basically, all of the unclean and dirty water goes into the portable vacuum's filter cartridge and clean water is returned directly back into the source.

Turn off the pump, remove the cartridge from its housing, and rinse/hose it off. It'll make a mess, but it will be wasted. This will push water through the hose and get all the air out.

The pool starts filtering normally by switching the valve to filter position through turning on the filter. This sounds like a good idea to me because it would give me the option of having the vacuumed water not go into my filter cartridge particularly. Pull the vacuum out of the pool when cleaning is done.

This directs dirty vacuum water through the pool filter to remove the contaminants, then conveys filtered water. You also need to clean the vacuum’s filters and strainer before you store the unit. Maintaining vacuum suction.loss of suction with a cartridge filter.

You can now vacuum your above ground pool with a cartridge filter without a hassle. Once cleaned, replace the cartridge, and turn the pump back on. Must be a broken filter pad.

Turn the filter’s on/off switch to the off position. The tight mesh filters out the impurities from the pool water.

How To Chemically Clean a Pool Cartridge Filter Pool